2019 03 08 Robot Arm
2019.03.07(pm): Water Pump Test with RAMPS 1.4
Calibration Initialization Move Sensors Water 2019 03 06 Water Pump Test
2019.03.06(pm) Voronoi sketch with python on Rhino
The Voronoi diagram is a picture in which the plane is divided into a set of closest points to a certain point. It is a pair relationship with the trine triangulation. It comes from the name of Georgy Feodosevich Voronoy. To draw a Voronoi diagram, first connect all the closest points of the points in …
Continue reading “2019.03.06(pm) Voronoi sketch with python on Rhino”
2019.03.06(am): How to use RAMPS 1.4
RAMPS 1.4 는 2019 03 06 RAMPS 1.4 Marlin
(Lecture Note) Autodesk Inventor – 4. Assembly
Make New Assembly file Click the Place Button Select Part file and Open in sequence Place the Part1 file Open the Part 2 file Constrain Constrain – Mate Joint Joint – Type Free Rotate Cylindrical Joint Cylindrical Joint is done Cylindrical Joint with Part 4 file (1) Cylindrical Joint with Part 4 file is done …
Continue reading “(Lecture Note) Autodesk Inventor – 4. Assembly”
(Lecture Note) Autodesk Inventor – 3. 3D modeling of part file (4)
3D modeling of Universal Joint – Part 4 Select the YZ Plane and Start 2D Sketch Draw a circle with diameter of 12.5 Extrude with both directions as 50mm Select the XZ Plane and Start 2D Sketch Draw a circle and Extrude as before Select the XY Plane and Sketch Draw a circle with diameter …
Continue reading “(Lecture Note) Autodesk Inventor – 3. 3D modeling of part file (4)”
(Lecture Note) Autodesk Inventor – 3. 3D modeling of part file (3)
3D modeling of Universal Joint – Part 3 Select the XZ Plane Sketch the circle with a diameter of 50mm Extrude up to 60mm Sketch on the YZ Plane Sketch as below Extrude cut with both directions Work Plane Offset from Plane Offset from Plane (42.124mm offset) 2D Sketch on the Work Plane Extrude Cut …
Continue reading “(Lecture Note) Autodesk Inventor – 3. 3D modeling of part file (3)”
(Lecture Note) Autodesk Inventor – 3. 3D modeling of part file (2)
3D modeling of Universal Joint – Part 2 Select the XZ Plane Sketch the circle with a diameter of 50mm Extrude up to 60mm Sketch on the YZ Plane Using Arc Tangent for Sketch Sketch as below Extrude cut with both directions Work Plane Offset from Plane Offset from Plane (42.124mm offset) 2D Sketch on …
Continue reading “(Lecture Note) Autodesk Inventor – 3. 3D modeling of part file (2)”
(Lecture Note) Autodesk Inventor – 3. 3D modeling of part file (1)
3D modeling of part file 3D modeling of Universal Joint – Part 1 Start 2D Sketch Select the YZ Plane Sketch as below Offset Closes the open section in a straight line. Extrude the Sketch Extrude the Sketch up to 60mm Select the top plane and Start 2D Sketch 2D Sketch on the top plane …
Continue reading “(Lecture Note) Autodesk Inventor – 3. 3D modeling of part file (1)”
(Lecture Note) Autodesk Inventor – 2. Practice of Sketch and Pitcher
Make First Part File Click the button “Start 3D Sketch” Overview Explore Drawing tools – Line and Circle Explore Drawing tools – Arc and Rectangle Sketch – Choose the Two Point Center Rectangle Dimension – a tool to determine the dimension Dimension – a tool to determine the dimension At this time, the dimension input …
Continue reading “(Lecture Note) Autodesk Inventor – 2. Practice of Sketch and Pitcher”